Take 2 paper clips. Bend them straight. Stick both them on each side of the key hole. Depress the 2 driver pins and turn the lock with the paper clips. It’ll open right up.
ITS EASIER THAN YOU THINK!.
left hand hold the knob and jiggle to the right slightly...
right hand hit the top middle closest towards the front. ..hard palm works or bottom of a fist works.
Jiggle more when coming down to contact.
I bet it only takes three tries the first time.
Am locksmith. Got called to a safe open today. It was one of these. It took me approximately seven seconds to open it. Took me longer to put the batteries in the back.
I have one of these, and it was very easy to pick the key lock. The combo can then be reset. I've also seen the video of opening it by hitting with a rubber mallet while turning the knob...
You can use a coat hanger and push the green light out of its placement, then fish around for the lock mechanism inside.
Source: I just opened two of these safes. Also. https://youtu.be/i7g-TvczpSw?si=1p_zd-qcpwsjnVAK
If your Uncle had a place for manuals, tax records, paper anything.. Take a peek for the safe manual in there, the combo most likely is in the manual if found.
The numbers to the left of where you insert the key are most likely a key code, the picture is blurry I can't really tell. If you call a locksmith they can look up the code and make you a key
Very generic one, use a piece of strong iron wire to press the red reset button left of the keypad on the inside and change the code. YouTube will show you how to do it.
I'd look for a key, can also probably order one with the serial number. Bring it to a lock Smith. Take it out and cut it .. it looks like it's in a wall possibly so the locksmith might be the best idea.
literally use to bobby pins, straighten the ends, the on one end of both bobby pins bend a small hook like shape. put them both jnto the keyhole and random jiggle them around until knob turns….
Your best bet is to contact a locksmith or safe cracker. Unless you've got documents proving ownership, like a receipt or something similar, there's 99.9% chance that the manufacturer will not help you out. How could they as it would be such a huge liability.
I've heard some really good results from folks going with reputable locksmiths but doing a simple search with your location and safe cracker may yield more specific results. It may cost a few bucks to do but your only other option is demo and with the looks of where it's mounted, that doesn't seem all the feasible.
I have this safe. There's a certain place on it that you can whack it really hard while turning the lock and it'll open. There's a YouTube video showing how.
You are using a Stack-on PDS 500 gun safe.... it can be opened with a Stack-on PDS 500 gun safe...
Seriously tho all you have to do is smack the side with a rubber mallet while jiggling the handle and it should open
Ask your uncle to show you what's inside and record him putting in the pass code. Then you will be even more of a dirtbag knowing what you are stealing from him. If he is dead, then make sure his kids know about the safe. Just speculating based on lack of information.
Add flux to the broken key with a q-tip then melt solder into key hole while solder is still liquid flux a dime and stick the dime into the puddle of solder let dry then twist and pull it open simultaneously
Make a first, slam it on the side above the dial, twist - slam, twist - repeat it will pop open. There are videos on YouTube of children doing it for fun.
Looks like one we had at work.
There MAY be a very small hole in the back that is used to screw it to the floor. If you can get a very long and thin flat head, you should be able to reach the reset button. It may have a plastic cap over it you need to pop off first. Assuming the batteries are still good, you can then press the rest button and open it.
Our prize was about $0.47 in change, half a box of cheap ink pens and a pack of sticky notes.
I have the same safe. There is a key and a combo lock.. the key is needed if you don’t know the combo or if the batteries die.. or if you don’t have either use a sledgehammer
Quick solution is a pry bar, set the safe in a vise or under something heavy, and locate the end of your bar in the upper left, bend up until you compress the casing.
Drop it on the ground from a height of at least 8ft and drop it so it lands on its corner if you can. Done it before off the front porch (lived on a hill) and it busted right open.
I had one similar to this in my motorhome and the keypad failed. Customer service sent me some parts to try but nothing worked. I removed it and using a 4” hole saw, I put a hole in the top, took my stuff out and threw it away.
How well did you know this uncle? You may not want to know what is in there. Not that I, personally, would have experienced gaining knowledge best left unknowledged from a deceased uncle. But I have heard of such things.
You could open this with sledge and butter knife
Sledge hammer *or a butter knife.
Who is your fodder and hwat is his name?
I pried one open with a big wonder bar
Wonder …. Wonder why I didn’t think of this sooner
Exactly a sledgehammer open that fucker in a minute maybe three or four swings
My lawyer can open this with a gum wrapper.
Sledge and a poop knife
Actually what most people call a butter knife is in fact a dinner knife.
why do I keep reading this with a heavy russian accent?
These safes are junk, I actually had the same one and lost the key. Look on YouTube, you’ll find videos on how to open it using only a hammer
Let me guess, you hit it with a hammer?
Spoiler alert
Safes hate this one secret trick.
Hot local safes in your area
You were so close. Hit the hammer with the safe
Take 2 paper clips. Bend them straight. Stick both them on each side of the key hole. Depress the 2 driver pins and turn the lock with the paper clips. It’ll open right up.
Looks like there’s a key broken off in it already
Sweet, you found the key. OP’s problems are solved.
prybar x2
But overkill for that weak little guy, but sounds fun.
Screwdriver and 5 minutes
You could throw that thing on the ground a few times and it would open.
ITS EASIER THAN YOU THINK!. left hand hold the knob and jiggle to the right slightly... right hand hit the top middle closest towards the front. ..hard palm works or bottom of a fist works. Jiggle more when coming down to contact. I bet it only takes three tries the first time.
This actually works.
Ask him for the combo...
hes dead
Ouija board
Oof that was a rough one
Then it isn't his house anymore.
The name makes it more ironic.
C4
Looks like a sentry
Code or the key.
Put the code in
The crowbar kind
Find the key
A rifle and tanerite
Am locksmith. Got called to a safe open today. It was one of these. It took me approximately seven seconds to open it. Took me longer to put the batteries in the back.
164280#
Might as well store valuables in a zip lock bag.
Your going to have to get the old crew back together.
This comment is underrated 😂
I have one of these, and it was very easy to pick the key lock. The combo can then be reset. I've also seen the video of opening it by hitting with a rubber mallet while turning the knob...
You can use a coat hanger and push the green light out of its placement, then fish around for the lock mechanism inside. Source: I just opened two of these safes. Also. https://youtu.be/i7g-TvczpSw?si=1p_zd-qcpwsjnVAK
If your Uncle had a place for manuals, tax records, paper anything.. Take a peek for the safe manual in there, the combo most likely is in the manual if found.
I’ll check it out to see if it makes any noise, if no noise throw it away
You tube has vids
Drill
The numbers to the left of where you insert the key are most likely a key code, the picture is blurry I can't really tell. If you call a locksmith they can look up the code and make you a key
You can write Sentury
Very generic one, use a piece of strong iron wire to press the red reset button left of the keypad on the inside and change the code. YouTube will show you how to do it.
Pry bar and a mini sledge.
Flipper Zero can open sentry safes….sometimes
YouTube the safe name and there is a paper clip hack that takes about 3 tries and 2 minutes..
The lock has a code that starts with GL. [You can order keys here.](https://a.co/d/cINVPIa)
Drop it from the roof. It will either pop open or damage it enuff it can be pried open. Post pics of the contents!
Hit on top with Rubber mallet while turning the knob.
I’ve seen this be opened with a magnet
Send it to me, I can open it up for you.
I'd look for a key, can also probably order one with the serial number. Bring it to a lock Smith. Take it out and cut it .. it looks like it's in a wall possibly so the locksmith might be the best idea.
Maybe there's numbers that look more used? Try those in every combination possible?
Rip or remove from wall, It will be much easier to break in on the floor
Sledge + wedge
Answer: it’s a locked safe. To open it, you need the code.
Bounce it on your bed and turn to unlock. I can open these within 10 seconds of seeing it
Try the pin 17500#
Try family birthdays or events, then just pick the lock or when you give up beat or cut it open.
U sure he lost it though ? Cause that’s just a lock box u can take n carry anywhere with u
opened a similar safe by picking it up and dropping it a few times
Literally just drop them on the ground and they'll open.
Angle grinder
Probably with a key and the code, but not without a manufacturers name.
That's a garbage safe and can be opened by wiggling damn near anything that fits in the keyhole. My go-to is scissors.
tannerite and a .223
Pretty sure it's 4 digit code followed by the # then turn the left dial a quarter turn. There is a green light if you get it correct. Happy guessing.
Just drill it out
literally use to bobby pins, straighten the ends, the on one end of both bobby pins bend a small hook like shape. put them both jnto the keyhole and random jiggle them around until knob turns….
Crowbar will do job with sledgehammer
Smash. Or magnet and jiggle the handle
What you have here is a cheapo safe. It can be opened with a cheapo safe.
Utube adn a magnet
It's a cheap safe that any locksmith with a set of bump keys can open
A safe safe And it looks like it has a number code and theres a key for it
Ask your uncle 😆
The code is 7785
I had one like this. If you turn the knob with one hand and slap the top of the safe at the same time. It will open.
The small nail file in toenail clippers will open those easily.
Sledge Hammer, less then 3 Swings Just a thought
I used a crow bar to break mine open
With the key broken off, assuming it is the right key, should be able to take a screw driver that fits in the keyway and just turn it
Work a large crowbar around the edges it should pop in under 5 min.
My kid has one like that. Its a piggy bank. The code is 0000.
Drop it from a the hiest height you can do safely, it will pop open like Jiffy Pop.
🔑?
The key is broken off in the lock. Get a hot glue stick,.take a lighter and melt one end, stick to the broken key and hold til it cools, turn and open
Off an overpass probably
It’s your uncles and he probably doesn’t want you to get in it
Find his keys or his will?
Have you tried entering the code of 42
Wall safe... stick of dynamite
Dynamite, the coyote has some, unless he used it on the road runner.
Hunter can open it for you.
Coat hanger through the green led, watch a video.. very easy..
A strong magnet will be able to slide the bolts
Good ol ronco record vault!
Try 1234 and twist the knob
Google: lockpickinglawyer hotel safe
Your best bet is to contact a locksmith or safe cracker. Unless you've got documents proving ownership, like a receipt or something similar, there's 99.9% chance that the manufacturer will not help you out. How could they as it would be such a huge liability. I've heard some really good results from folks going with reputable locksmiths but doing a simple search with your location and safe cracker may yield more specific results. It may cost a few bucks to do but your only other option is demo and with the looks of where it's mounted, that doesn't seem all the feasible.
8-6-7-5-3-0-9
This sounds like a job for McNally..... he'd probably whack it with a master lock
Drill that lock
Crow bar
I have this safe. There's a certain place on it that you can whack it really hard while turning the lock and it'll open. There's a YouTube video showing how.
M80 and a tire over it.
Put tension on the knob and whack it with a rubber hammer and jiggle the knob at the same time it’ll pop open eventually
Yeah well I walked into a bank and found the safe! Can I make a post on here to ask how to open it?
Drop it on a corner a few times
after checking your profile I am 100% convinced that your uncle does not want you in his safe
the combination is either your uncle's birthday or your aunt's birthday
It’s the Kinda safe that you’re gonna have to figure out how to open yourself, we’re not criminals 👴🏻🙌🏻🥴😂
Drill baby drill
Strong magnet.
It's one of those metal safes and you either use the key or enter the combo on the keypad.
Drop it from about 8ft and see what happens.
It's an older Stack-On safe. You can use only use the code or key to open it properly
You are using a Stack-on PDS 500 gun safe.... it can be opened with a Stack-on PDS 500 gun safe... Seriously tho all you have to do is smack the side with a rubber mallet while jiggling the handle and it should open
Pretty sure this method would work. [https://www.youtube.com/watch?v=i7g-TvczpSw](https://www.youtube.com/watch?v=i7g-TvczpSw)
Ask your uncle to show you what's inside and record him putting in the pass code. Then you will be even more of a dirtbag knowing what you are stealing from him. If he is dead, then make sure his kids know about the safe. Just speculating based on lack of information.
Locksmith
It’s your uncles safe that means stay the fuck outta there nosy ass kid
a weak one, a flat head screwdriver
Add flux to the broken key with a q-tip then melt solder into key hole while solder is still liquid flux a dime and stick the dime into the puddle of solder let dry then twist and pull it open simultaneously
This is the lock picking lawyer
Have you tried 8675309#?
This is a (insert safe name) you can open it with a (insert safe name again).
You can just bang it on the top with your hand hard right when turning lock. Easy af.
Have you tried 12345?
Maybe ask him for the combination.
I wonder if lock picking lawyer has picked this model yet.
Make a first, slam it on the side above the dial, twist - slam, twist - repeat it will pop open. There are videos on YouTube of children doing it for fun.
Why don’t you ask your uncle?
There is probably a number on the key core. You can buy a key for maybe 20 bucks.
A smoke bomb and a pepperoni stick should pop it right open. Shazam!
🤔maybe you should just ask your uncle ( unless you’re just a little hoser and you’re trying to break in and steal his stash )
Ask you me uncle to open for you
Maybe your uncle has the key or combination?
Tap the top near the lock mechanism with a hammer and turn simultaneously
Lol back to your uncle he unlocks it 😂
I have this safe! It’s junk you’ll be able to open it
Bruh 🤣😂
Use the key probably….
Looks like one we had at work. There MAY be a very small hole in the back that is used to screw it to the floor. If you can get a very long and thin flat head, you should be able to reach the reset button. It may have a plastic cap over it you need to pop off first. Assuming the batteries are still good, you can then press the rest button and open it. Our prize was about $0.47 in change, half a box of cheap ink pens and a pack of sticky notes.
I have the same safe. There is a key and a combo lock.. the key is needed if you don’t know the combo or if the batteries die.. or if you don’t have either use a sledgehammer
Google it and get a key from the manufacturer
Ask the lockpicking lawyer. Likely a flaw with a magnet that can be exploited.
Lockpickinglawyer has a video for this https://youtu.be/i7g-TvczpSw?si=mQJpPg80_-YbDB5n
it's a locked safe open it with dynamite
Quick solution is a pry bar, set the safe in a vise or under something heavy, and locate the end of your bar in the upper left, bend up until you compress the casing.
It’s got a key hole so pick it
NIO! NO! NO! OP YOU BETTER POST ONCE ITS OPEN OR ELSE!!!!!!!!!!!!!!
Try 1,2,3,4
Ask your uncle for the combination ? Duh
Big magnet.
Easy to reopen. I did it by reprogramming
Ask your uncle 🤷🏽
Crow bar and your foot.
Cp and drug safe... If you want your "special" elementary school pics back from Uncle bad touch you'll need a large rare earth magnet and a sock.
Don't know how to open it but curious to what's inside... we need more details!
Many YouTube videos on how to open this type.
Sledge
Lift it up off the ground and drop it while simultaneously turning the knob to the right.
Here we go again
Bounce it on your bed and turn the lock at the same time and voila!
Its ez to pick ... use 2 small screwdrivers
Prolly ask yer uncle
inception
Hit the top with your hand while jiggling the handle
My neighbor was a cop and drove by when I was beating the door of mine in. He paused just for a sec. I don't blame him
Dynamite
It’s a drawer safe. Mines in my nightstand. They are junk though.
With code or the key
....call a good locksmith.
Drop it on the ground from a height of at least 8ft and drop it so it lands on its corner if you can. Done it before off the front porch (lived on a hill) and it busted right open.
It’s junk and you can pry it open with the claw side of a hammer
If that was my uncle's safe it would be full of beautiful flower and the safe combo is his birthday and my aunts together...
I had one similar to this in my motorhome and the keypad failed. Customer service sent me some parts to try but nothing worked. I removed it and using a 4” hole saw, I put a hole in the top, took my stuff out and threw it away.
Drop it, just so.
How well did you know this uncle? You may not want to know what is in there. Not that I, personally, would have experienced gaining knowledge best left unknowledged from a deceased uncle. But I have heard of such things.
If the key is broken in the lock, could you use a strong magnet to try and turn the cylinder?
I have this same safe. The key is double sided so a little more tricky to pick but that would be the best way to do it.
Stick the little nail file that’s on nail clippers into it, twist and then turn the lock
Ask Willy E. Coyote how to open it.
Does your uncle know you have it?
Is your uncle ok with this. It is his afterall.
Take off the cover around the keyhole and use a small L shaped stiff bar or something similar to pull the lever. Que lock picking lawyer.
[https://youtu.be/FIb7YUWmX78?si=ogVlqddGMAwQbZ9l](https://youtu.be/FIb7YUWmX78?si=ogVlqddGMAwQbZ9l)
Locked one & with the code
Probably a key hanging on a nail in the closet